Results 1 to 5 of 5

Thread: DMK 23GV024 installation

  1. #1
    Join Date
    Jan 2013
    Location
    Haifa, Israel
    Posts
    8

    DMK 23GV024 installation

    Hi
    I'm having trouble with connecting the camera - DMK 23GV024.
    I set the IP address of 169.254.0.1 Mask 255.255.0.0, but the computer detects an "undefined network" and "No Network access".
    I applied 12V to pins 1 (+) and 6(GND)
    Last edited by Alexander; September 1, 2013 at 12:59:03.

  2. #2
    Join Date
    Jan 2003
    Location
    Bremen, Germany
    Posts
    4,886

    Re: DMK 23GV024 installation

    Alexander,

    this link local IP address of the camera is normal, if the camera runs on DHCP and there is no DHCP server availalbe, that provides a matching IP address for the camera. I suppose, the camera is connected directly to your computer and your network adapter has a fixed IP address. If so:
    The fixed IP addresses should be:
    Networkadapter:
    192.168.1.1 : 255.255.255.0
    Camera:
    192.168.1.2 : 255.255.255.0

    In case, the computer and camera run in a network with a DHCP server and the camera is connected to a switch, then following can happen: Switch on power of computer, switch and camera. The camera boots faster than the switch and therefore, no DHCP server is found. Then the camera uses the link local IP address. In this situation use either fixed IP addresses or dis- and reconnect the camera.

    Background information quoted from RFC 5725

    169.254.0.0/16 - This is the "link local" block. As described in
    [RFC3927], it is allocated for communication between hosts on a
    single link. Hosts obtain these addresses by auto-configuration,
    such as when a DHCP server cannot be found.

    http://tools.ietf.org/html/rfc5735
    Best regards
    Stefan
    IC Imaging Control Support

  3. #3
    Join Date
    Jan 2013
    Location
    Haifa, Israel
    Posts
    8

    Re: DMK 23GV024 installation

    Stefan!
    I was able to join the camera only on Intel Atom N450 Win XP Embedded Ser. Pack 3
    On IPconfig.ehe I see my camera - DMK 23GV024, but when I click on this raw there is a warning on the left. When I do a Disable/Enable camera reappears in IPconfig.exe.
    IC Capture does not see the camera
    I checked DirectX, it is Version 9.0

  4. #4
    Join Date
    Jan 2003
    Location
    Bremen, Germany
    Posts
    4,886

    Re: DMK 23GV024 installation

    If there is a warning, then the camera is not configured correctly to your computer's network. You can pass a temporarily fixed (persistent) IP address to the camera and if this is working, you can pass the correct IP address to the camera in a second step.

    In case, this does not work, I must know, how your network is configured. Is there a switch? what are the IP addresses of the network controller? Are all devices GigE devices. Without this, I would continue guessing around.
    Best regards
    Stefan
    IC Imaging Control Support

  5. #5
    Join Date
    Jan 2013
    Location
    Haifa, Israel
    Posts
    8

    Re: DMK 23GV024 installation

    Thank you Stefan,

    All is OK!

Similar Threads

  1. Does DFK 23GV024 have multislope?
    By lxltaibo in forum IC Imaging Control C++ Class Library
    Replies: 1
    Last Post: April 18, 2013, 08:16:11
  2. DBK 21AU618 installation problem
    By Vitor Quinta in forum Astronomy Cameras Support Forum
    Replies: 8
    Last Post: October 24, 2012, 08:55:47
  3. USB driver installation problem
    By ATTILA.B in forum Hardware and Driver
    Replies: 2
    Last Post: February 17, 2012, 13:12:06
  4. Driver Installation
    By kevin3d3 in forum Hardware and Driver
    Replies: 3
    Last Post: April 1, 2010, 10:18:54
  5. installation error
    By Unregistered in forum IC Imaging Control ActiveX
    Replies: 2
    Last Post: December 12, 2002, 13:13:17

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •