Results 1 to 8 of 8

Thread: IC Imaging Control 3.2 and Matrox MIL 9.0

  1. #1
    Join Date
    Feb 2012
    Location
    Joinville, SC, Brazil
    Posts
    5

    IC Imaging Control 3.2 and Matrox MIL 9.0

    Hi,

    I downloaded the IC "Matrox MIL Extension" from the download section and when I try to install I get a message that says "IC Matrox MIL Extension requires at least IC Imaging Control 3.0, which was not found on your computer. Install anyway?", but I have IC Imaging Control 3.2 installed, What I missed out?

    Can I proceed with the installation? It'll work?

    Regards,
    JPriori

  2. #2
    Join Date
    Jan 2003
    Location
    Bremen, Germany
    Posts
    4,250

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    Hello,

    I am very sorry, but we stopped the Matrox MIL support.
    Best regards
    Stefan
    IC Imaging Control Support

  3. #3
    Join Date
    Feb 2012
    Location
    Joinville, SC, Brazil
    Posts
    5

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    Hi,

    Thank you for the information. Can you tell me since when you stopped the support? Because I have a image software that uses Matrox MIL 8.0 and your cameras and an older version of IC Imaging Control.

    Regards,
    JPriori
    Last edited by JPriori; March 2, 2012 at 12:01:10.

  4. #4
    Join Date
    Jan 2003
    Location
    Bremen, Germany
    Posts
    4,250

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    This was two years ago, if I remember correctly.

    It seems, you do not have IC 3.0. I can send this to you by email, therefore, please create a support case at http://www.imagingcontrol.com/support/case/
    Best regards
    Stefan
    IC Imaging Control Support

  5. #5
    Join Date
    Feb 2012
    Location
    Joinville, SC, Brazil
    Posts
    5

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    Hi,

    Thank you again, you are correct, I use IC 3.0 with my actual version but we decide to stop the development a moment and now we decide to create a brand new version.

    Well I'll need to figure it out what to do now.

    Regards,
    JPriori

  6. #6
    Join Date
    Jan 2003
    Location
    Bremen, Germany
    Posts
    4,250

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    The major changes from IC 3.0 to 3.2 is in the .NET part, 64 bit support and handling of ROIs for our 72er camera models. Therefore, it may be is not necessary to update to IC 3.2 for you.
    Best regards
    Stefan
    IC Imaging Control Support

  7. #7
    Join Date
    Feb 2012
    Location
    Joinville, SC, Brazil
    Posts
    5

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    Thank You for your reply. But I need 64bit support. thank you.

    Regards,
    JPriori
    Last edited by JPriori; March 8, 2012 at 17:44:11.

  8. #8
    Join Date
    Jan 2003
    Location
    Bremen, Germany
    Posts
    4,250

    Re: IC Imaging Control 3.2 and Matrox MIL 9.0

    Hello,

    I am very sorry, but an IC MIL Extension 64 is not available.
    Best regards
    Stefan
    IC Imaging Control Support

Similar Threads

  1. Using Imaging Control without a GUI
    By Mikkel Engbo in forum IC Imaging Control .NET
    Replies: 2
    Last Post: July 23, 2010, 13:39:35
  2. DFG Grabbing with Matrox lib. processing
    By Unregistered in forum IC Imaging Control C++ Class Library
    Replies: 7
    Last Post: January 2, 2008, 11:24:10
  3. IC Imaging Control
    By Unregistered in forum IC Imaging Control .NET
    Replies: 1
    Last Post: August 3, 2005, 12:37:11
  4. IC Imaging Control + Matrox
    By accforsanjay in forum IC Imaging Control ActiveX
    Replies: 0
    Last Post: October 5, 2004, 11:48:20
  5. Use of IC imaging Control in DLL
    By Unregistered in forum IC Imaging Control ActiveX
    Replies: 5
    Last Post: January 8, 2003, 09:59:46

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •